 |
 |
 |
|
|
|
 |
 |
| 914 RACE PARTSDry & Wet oil sump:
Designed to provide a 2 to 1 scavenge to pressure ratio. All pumps designed to deliver constant oil pressure at all temperatures under all racing conditions.
Dry sump oil tank with A/N threads comes complete with oil cap and mounting straps
Racing valve lash caps
Valve retainers for Hi-rev valve springs. Heat treated for strength and reliability.
Hi-rev silicone valve springs. Increases spring tension at full lift without increasing seat pressure for maximum RPM. For total valve control through all RPM ranges. Made specially processed steel tested and proved in racing applications, to insure against breakage.
Hi-rev valve spring adjusting shims. These shims are for adjusting proper spring height like the 911 Porsche cars. Hi quality for reliability.
Valve covers bolt on type for leak restriction, aluminum to dissipate heat (like the 911 Porsche), cooling fins and designed to clear hi-lift rocker assemblies. Complete kit with hardware and gaskets, no modifications.
Oil Deep Sump kit. Deep sump adds an additional 2 quarts, for racing and autocrossing. This is a direct bolt on kit. From aluminum with cooling fins, this will add a longer life to your Porsche 914.
Heavy duty STEEL oil pump. This is a High volume oil pump, made out of steel for strength and reliability. Gives your motor over 40% high volume capacity. This is a must for any performance 914 Porsche either for street fun or racing.
Billet racing lifters. Finest quality , made from Iron billets. Precision ground for longer life and quality for maximum RPM loads.
Universal sandwich oil cooler adapter and fitting
Cylinder Shims for adjusting correct deck height
Performance Rods are a very popular set up that Motor Meister sells. All Performance rods come balanced end to end, shotpeened, and magnufluxed.
Carrillo Rods are one of the strongest and most used for Racing application. Using SPS bolts and nuts, and H-beam rod construction.
Oil cooler block off for running full flow set-ups.
Fuel Pump block off for running electrical fuel pump, and can be used as a breather plate.
Rocker assemblies complete with factory 911 Porsche adjusters, chromoly spacers and micro polished shafts.
Rocker spacers out of 4130 chromoly which you can remove the original thrust springs.
Valve adjuster Factory 911 Porsche. ( these are not copies ).
Performance cams for the Porsche 914 we sell are grinds specially designed for performance applications. All profiles thoroughly developed and tested to insure maximum cylinder flow and horsepower. Ground from new billet cores. Cam flange has been drilled for a bolt on gear, like the Porsche 911.
Push rods new aluminum, all hand checked for straightness.
Push rod tubes all factory Zinc plated for corrosion and fit.
Motor Meisters oil cooler kits are very popular. The cooling efficiency you receive is like night and day. All coolers are stacked plate design, which offers you the best cooling possible. All coolers are aircraft quality aluminum, fluxless oven brazed construction. Come with ½ female pipe thread. They come already painted black to dissipate heat fast. These coolers come in many different sizes.
Cylinder Shims 100mm for stroking engines. This eliminates machine pitons when using a stroker crank. Precision machined and ground for exact tolerances.
Piston and cylinder kits. P/L kits come with pistons, cylinders, rings, pins and clips.
Performance Hi compression Pistons. These pistons are billet stock and are light weight. They come custom built to your exact application, including valve pocketing. Come in any size you may need.
Piston Pins light weight. These piston pins are light weight, and are very strong to with stand racing applications. Taking weight of the movable mass.
Performance piston rings made by Total Seal.
Racing Piston pin clips.
Flywheels lightened 200mm 12-13lbs.
Clutch Discs and pressure plates.
911 Porsche type fan assembly. Uses 911 fan, alternator assembly, which includes, fiberglass fan housing, 911 pulley, nut, washer, shims, keyway, belt, bracket, strap and hardware with instructions.
Dual Weber carburetor kit. Kit comes with Weber carbs, manifolds, linkage, gaskets and air filters.
Ignition distributor. Complete Bosch dist. With cap, rotor, points and condenser. This dist. is centrifugal advance, ready for installation.
Exhaust systems for the Porsche 914. Braided Stainless Steel hose is reliable and maintenance free.
Performance Heads: Motor Meisters performance heads are from German cores and are completely rebuilt and are proven winners in all types of performance applications. |
|
 We accept major Credit Cards! |
|
 |
|
or e-mail MeinPorshe@aol.com |
 |
| 914 Racing | 356 & 912 Performance | Contact Us | Order Parts On-Line | |
|
|
|
|
|
|
|
|
|
|
=================================================== |
|
