 Crowfoot
Heavy duty factory type tool for removal
of the cam nut and installation on a Porsche.
911 Porsche only
$20.00 rental or $89.95 cost
Cam holders for Porsche
For installing and removing cam nut. Keeps
the cam from turning.
1965-1980½ 911 Porsche only
$10.00 rental or $34.95 cost
1980½ - 1996 911 Porsche only (for the
type that does not use the crowfoot tool)
$20.00 rental or $84.95 cost
Pin Remover for Porsche
Removes cam sprocket pins.
911 Porsche only
$2.00 rental or $3.95 cost
Chain Tensioner holder for Porsche
Allow removal of clip prior to chain tensioner installation.
911 Porsche only
$5.00 rental or $19.95 cost
Piston pin remover for Porsche
Removes piston pin from piston
911 Porsche only
$5.00 rental or $19.95 cost
Allen 911 Socket tool
Extra long for reaching nuts. 8mm Heat exchanger or 10mm head nuts.
8mm 911 - $10.00 rental or $24.95 cost
10mm 911 - $10.00 rental or $29.95 cost
Flywheel Allen Socket
This is a top quality 12 point allen tool for removing and installing the flywheel
bolts on a Porsche 911.
$20.00 rental or $89.95 cost
Carburetor Sychrometer
This is the best carb tool and a must for anyone owing triple barrel carbs. It fits
right inside of the stacks for no air leaks at all. Only one is needed.
$20.00 rental or $74.95 cost
Econo. Carburetor Sychrometer
For synchronizing your carbs and you do not
want to spend a lot of money this little tool is hard to beat for the price.
$10.00 rental or $39.95 cost
Dial
Gauge
This dial gauge will help you in setting your cam timing, checking your
intermidateshaft run out, flywheel depth or any precise measurement you may need to check
for either inspecting wear limits or adjusting or setting proper measurements.
$64.95 cost
Sealant Spread
Brushes Set of 12 Horse hair bristles
Metal tubular handles
6-1/8'' overall length
$6.95 cost |
 Flywheel
lock for Porsche
Locks flywheel when removing gland nut
911, 356 & 912 Porsche
$10.00 rental or $29.95 cost
Dial indicator holder for Porsche
A must for valve timing. Will take all standard dial indicators.
911 Porsche only
$15.00 rental or $39.95 cost
Piston ring compressor for Porsche
Compresses rings for installation of piston.
83mm - 94mm or 88mm - 94mm
356, 912, 914, & 911 Porsche
$5.00 rental or $9.95 cost
Clutch installation tool
Aligns clutch disc
356 & 912 Porsche
911 Porsche
$5.00 rental or $9.95 cost
Cylinder holding nuts for Porsche
Holds cylinders against case while installing pistons.
911 Porsche only (kit of 6)
$10.00 rental or $34.95 cost set of 6
Chain Sprocket Tension Tool
If you do not want your timing chain to skip a tooth, this little tool is a must. This
tool keeps chains snug against the sprockets for no slipping at all.
$10.00 rental or $24.95 cost
Crankshaft
Assembly Holder
To assemble your connecting rods on to your crankshaft with out the assembly
rolling all over the place the crankshaft assembly holder is a great tool, adjustable for
any other motors and soft wood cradles to not damage the crankshaft journals
$25.00 rental or $69.95 cost
574 Loctite
574 Loctite is the ONLY case sealant to use when reassembling your Porsche motor.
With the expansion that your magnesium and aluminum heads, case and other internal parts
go through you will need a sealant that will move with the expansion of these parts. Other
sealants will crack their bonding action or will get brittle with heat and start leaks
later on. This is not the cheapest sealant made but the very best. 574 Loctite is the same
sealant that Motor Meister uses on their own rebuilt street and racing motors.
$24.95 cost
European
Thread Locker
European Thread Locker is the best for flywheel bolts, rod bolts, front pulley
bolts, head studs or any loose hardware you do not want coming off later while driving
your Porsche. This is the same thread locker that Motor Meister uses on their own rebuilt
street and racing motors.
$19.95 cost
Part Cleaning &
Polishing Brush Set Brush head size: 1-3/8''
1-Nylon (Soft)
1-Brass (Medium)
1-Steel (Firm)
$6.95 cost
|
